Peter: 1 Version importiert

2023-10-31T08:03:08Z

1 Version importiert

← Nächstältere Version	Version vom 31. Oktober 2023, 10:03 Uhr
(kein Unterschied)

en>Peter: 1 Version importiert

2023-08-22T19:35:49Z

1 Version importiert

Neue Seite

The firmware and bootloader binaries as well as the lens calibration file can be found on the customer support CD in our download section: https://support.bluetechnix.com/software/

===Argos 3D - P310 Update with Network Configured Bootloader===
Since booloader V1.2.0 and firmware V2.0.0 the Argos 3D P310 also supports a network configured bootloader mode, which preserves the user configured network settings (IP address, MAC address, subnet mask, gateway IP). After an update to a supported firmware version it will save these settings to NVM as a user register map. Please note that any other user defined register settings will still be reset to factory settings.

Currently this procedure is only supported when 'updating' from firmware V2.0.0 to V2.0.0 using bootloader V1.2.0.

Please refer to the Argos 3D P310 Software User Manual for details on the Network Configured Bootloader Mode.

===Argos 3D - P310 Bootloader Update===

A bootloader update will wipe your firmware and the register map.
The camera is reset to factory state.

'''Note: You have to ensure that power is stable during a bootloader update, otherwise the device may not respond anymore!'''

In order to update your Argos 3D - P310 bootloader, please follow these steps:
# Download the bootloader binary loader file provided by Bluetechnix.
# Download and start the BLT-ToF-Suite provided by Bluetechnix.
# Connect to the Argos
# Make sure your camera is connected and accessible via TCP/IP.
# When the camera is in bootloader mode it toggles its alive led every second; register Mode 0 also tells the current state.
# If not in bootloader mode, open Utilities/Downloader and click on "Start boot loader".
# Be sure to be in bootloader mode and wait for the camera to initialize properly.
# Select "Bootloader" from the dropdown menu button.
# Click on "Choose file..." and select the bootloader binary provided by Bluetechnix.
# Click on "Flash update" and wait for the popup window saying "Flash update finished successfully".
# Click on "Reset device" to reboot the Argos
# The camera boots the new bootloader and is ready to flash a firmware.

===Argos 3D - P310 Firmware Update===

A firmware update will wipe your register map.
The camera is reset to factory state.

In order to update your Argos 3D - P310 firmware, please follow these steps:
# Download the firmware binary loader file provided by Bluetechnix.
# Download and start the BLT-ToF-Suite provided by Bluetechnix.
# Connect to the Argos
# Make sure your camera is connected and accessible via TCP/IP.
# When the camera is in bootloader mode it toggles its alive led every second; register Mode 0 also tells the current state.
# If not in bootloader mode, open Utilities/Downloader and click on "Start boot loader".
# Be sure to be in bootloader mode and wait for the camera to initialize properly.
# Select "Application" from the dropdown menu button.
# Click on "Choose file..." and select the firmware binary provided by Bluetechnix.
# Click on "Flash update" and wait for the popup window saying "Flash update finished successfully".
# Click on "Reset device" to reboot the Argos
# The camera boots the new firmware and is ready for use

===Argos 3D - P310 Lens Calibration Update===

When using a different lens than the standard lens it is necessary to flash new lens parameters. Please get in contact with Bluetechnix to get further support for different lenses.

In order to update your Argos 3D - P310 lens parameters, please follow these steps:
# Download the lens parameters binary file provided by Bluetechnix
# Download and start the BLT-ToF-Suite provided by Bluetechnix
# Connect to the Argos
# Make sure your camera is connected and accessible via TCP/IP
# Select "LensCalibration" from the dropdown menu button.
# Click on "Choose file..." and select the calibration file provided by Bluetechnix.
# Click on "Flash update" and wait for the popup window saying "Flash update finished successfully".
# In any X/Y/Z image mode the 3D data adjusts to the new lens immediately

Argos 3D - P310 Firmware Update - Versionsgeschichte

Peter: 1 Version importiert

en>Peter: 1 Version importiert