Peter: 1 Version importiert

2023-10-31T08:03:11Z

1 Version importiert

← Nächstältere Version	Version vom 31. Oktober 2023, 10:03 Uhr
(kein Unterschied)

en>Peter: 1 Version importiert

2023-08-22T19:35:53Z

1 Version importiert

Neue Seite

== Introduction ==

Bluetechnix offers a Board Support Package that is based on the '''U-Boot boot loader''' and the '''Buildroot''' with '''Linux kernel'''.

=== Support ===
*blackfin.uclinux.org has a great '''documentation''' Wiki: https://docs.blackfin.uclinux.org
*For other questions and issues belonging to uClinux and Blackfin, you may search in the [https://ez.analog.com/community/dsp/software-and-development-tools/linux-blackfin official Blackfin uClinux forum]

=== Development host setup ===
We are using Linux distribution '''Ubuntu 10.04 LTS''' on the development host.

*Ubuntu uses dash as the preferred shell. However, we want bash. So, reconfigure ''/bin/sh'' to point to ''/bin/bash'' instead of ''/bin/dash'':
sudo dpkg-reconfigure dash
Select no when asked if it should link dash to /bin/sh.

*You probably need access to the [[Serial console|serial console]] (UART1) which is available via the USB-UART converter.
*We recommend to install a [[TFTP Server]].
*Optionally, you may want to set up a [[DHCP Server]].

== Releases ==

=== Release 1.0.1 ===
;Release date
:2015-09-22
;Supported hardware
:eCM-BF609-C-C-Q25S256F8
:eCM-BF609-C-I-Q25S256F8
:eDEV-BF609
;Download path
:https://support.becom-group.com/releases/blackfin/eCM-bf609/
;Base board support package
:Analog Devices 2013R1-RC1
;Used tool chain
:Analog Devices 2013R1-RC1
;Release Notes
:For information about supported features have a look at the [[#Support Matrix]]
;Changes
:- Fixed Ethernet PHY connection problems

=== Release 1.0.0 ===
;Release date
:2013-12-02
;Supported hardware
:eCM-BF609-C-C-Q25S256F8
:eCM-BF609-C-I-Q25S256F8
:eDEV-BF609
;Download path
:https://support.becom-group.com/releases/blackfin/eCM-bf609/
;Base board support package
:Analog Devices 2013R1-RC1
;Used tool chain
:Analog Devices 2013R1-RC1
;Release Notes
:For information about supported features have a look at the [[ECM-BF609 uCLinux Software User Manual#Support Matrix|Support Matrix]]
;Known issues
:- Ethernet PHY may not start correctly (workaround: additional reset).

== Support Matrix ==
We are working on basic support for our core module. This matrix gives you the current status.

Legend:
*OK = supported
*? = unknown
*NO = not supported (software)
*N/A = combination not allowed/not available/not relevant (hardware)

'''Bluetechnix offers custom development services! Feel free to [mailto:office@becom-group.com contact] us if you are missing support for specific hardware!'''

{| class="wikitable"
|+
||
||
| colspan="2" | eCM-BF609
|-
|| || || U-Boot || uClinux
|-
| rowspan="11" | eDEV-BF6xx || Ethernet || {{tcc|OK}} || {{tcc|OK}}
|-
|| SD-card || {{tcc|?}} || {{tcc|OK}}
|-
|| USB-OTG || {{tcc|?}} || {{tcc|OK}}
|-
|| Audio || {{tcc|NO}} || {{tcc|NO}}
|-
|| HDMI || {{tcc|NO}} || {{tcc|OK}}
|-
|| ISM-MT9M131 || {{tcc|NO}} || {{tcc|NO}}
|-
|| ISM-MT9P031 || {{tcc|NO}} || {{tcc|NO}}
|-
|| ISM-MT9M024 || {{tcc|NO}} || {{tcc|NO}}
|-
|| CAN || {{tcc|NO}} || {{tcc|NO}}
|-
|| LVDS || {{tcc|NO}} || {{tcc|NO}}
|-
|| Touchscreen || {{tcc|NO}} || {{tcc|NO}}
|-
|}
<span style="color:red">NOTE: HDMI is not enabled by default in the kernel configuration. For inforation how to configure HDMI see [[#HDMI|here]].</span>

== Getting started with eDEV-BF609 ==
* Plug in your eCM-BF609 on your eDEV-BF609.
* Default dip switch settings:
S1 00000001
S2 11111000
S4 1010
S6 1100
* Connect to the Board (X13) to your computer with a mini USB cable.
* Use your Serial Terminal Program of your choice with the following settings:
Baudrate: 115200
FlowControl: NONE
Parity: None
Stop Bits: 1
Data: 8Bit
* If you like, connect Ethernet.
* Connect 12V DC to the power connector.
<span style="color:red">NOTE: After power up the reset button must be pressed and hold for 1 seconds to boot correctly.</span>

== Install software sources ==
Download and extract the newest releases of the Buildroot und the U-Boot boot loader.
For Release 1.0.0 we used tool chain 2013R1_RC1 from https://sourceforge.net/projects/adi-toolchain/files/.
You have to add the path of your tool chain to your PATH variable.

== The U-Boot boot loader ==

The main task for the boot loader is to initialize hardware appropriately (especially the RAM), and to load the Linux kernel. Via environment variables, you can configure U-Boot as you wish: Network settings, where to load the Linux kernel from, set up the kernel's command line, etc.

In most cases, you will not need to change and recompile U-Boot, but simply alter the environment variables so that U-Boot's behaviour fits your needs.

=== U-Boot development ===
Build the u-boot for the eCM-BF608
cd bf609-u-boot
make ecm-bf609

====Environment storage====

The u-Boot environment is usually saved in the SPI flash.

====Linux loading and parameters====

Set the U-Boot variable ''bootcmd'' according to your wishes:
*<pre>set bootcmd run ramboot</pre>
: Loads the ''uImage'' via TFTP.
*<pre>set bootcmd run flashboot</pre>
: Loads ''uImage'' from SPI flash.

=== Updating ===
''NOTE: You can also update U-Boot from Linux. Here, we talk about updating U-Boot with a running U-Boot.''

You need to have your network configured. Set at least ''ipaddr'', ''serverip'', and ''ethaddr''.
<pre>run update</pre>

== Linux kernel development ==

* Change the buildroot configuration:
cd bf609-buildroot
make menuconfig
* Change the kernel configuration:
make linux-menuconfig
* Store your current kernel config:
cp output/build/linux-custom/.config linux/linux-kernel/arch/blackfin/configs/ECM-BF609_defconfig
* Build kernel
make
* Write uImage to flash
In u-Boot type:
tftp $(loadaddr) uImage;sf probe 1;sf erase 0x40000 0x7c0000;sf write $(loadaddr) 0x40000 $(filesize)
The uImgae gets loaded over TFTP and gets stored in the SPI flash at address 0x40000.

== Knowledge base ==

In alphabetical order.

=== Ethernet ===
{{Supporttable|eDEV-BF609|≥V1.0|}}
*Unit test for Linux (You must have TFTP server running on 192.168.0.2 which provides the file ''1MBrandomfile'' for the test to be successful):
/unit_tests/ethernet.sh
*U-Boot default network configuration:
**IP address 192.168.0.15
**Server IP address 192.168.0.2

=== SD card ===
{{Supporttable|eDEV-BF609|≥V1.0|}}
*Unit test /dev/mmcblk0
/unit_tests/sd.sh

=== USB OTG ===
{{Supporttable|eDEV-BF609|≥V1.0|}}
*The Linux driver for USB Host is automatically loaded (part of the kernel).
*If you want to test the port in device mode, then you have to load a gadget kernel module. For available gadgets, look into
bf609-buildroot/linux/linux-kernel/drivers/gadget/
*Note: Do not use the USB Host mode (e.g. connect a USB flash disk) while a gadget module is loaded. (We observed that the driver crashes.)
*Unit test; assumes that a USB disk is plugged into the USB-OTG port)
/unit/tests/usb.sh

=== HDMI ===
{{Supporttable|eDEV-BF609|≥V1.0|}}
You have to eanbele the v4l2 and display driver.
Device Drivers --->
<*> Multimedia support --->
[*] Cameras/video grabbers support
[*] Media Controller API (EXPERIMENTAL)
[*] V4L platform devices --->
<*> Blackfin Video Display Driver
[ ] Autoselect ancillary drivers (tuners, sensors, i2c, frontends)
Encoders, decoders, sensors and other helper chips --->
<*> Analog Devices ADV7511 HDMI transmitter

*Unit test
Prepare a 720p yuv file and transfer it to your board.
tftp -r image.yuv -g 192.168.0.2
Use v4l2_video_display to play this file on your tv.
v4l2_video_display -F image.yuv

[[Category:Blackfin|Blackfin]]
[[Category:eCM-BF609]]

ECM-BF609 uClinux Software User Manual - Versionsgeschichte

Peter: 1 Version importiert

en>Peter: 1 Version importiert