Argos®2D D100 Camera Quick start

This document describes various specifics of the Argos®^2D D100 camera.

Quick start

Here is how to start with your Argos®^2D D100 Camera development board based on the CM-BF561 SoM.

• Remove the Cover from the camera. It is already unscrewed and can be removed with gentle force.

Inside the Argos®^2D D100 Camera

Top side connector placement:

Bottom side connector placement:

• Configure the DIP switches on the base board for parallel flash boot.

| }}{{#if: 0 | | }}{{#if: 0 | | }}{{#if: 0 | | }}{{#if: | | }}{{#if: | | }}{{#if: | | }}{{#if: | | }}{{#if: | | }}{{#if: | | }}{{#if: 1 | {{#ifeq: 1 | 1 | | {{#ifeq: 1 | X | | }} }} | }}{{#if: 0 | {{#ifeq: 0 | 1 | | {{#ifeq: 0 | X | | }} }} | }}{{#if: 0 | {{#ifeq: 0 | 1 | | {{#ifeq: 0 | X | | }} }} | }}{{#if: 0 | {{#ifeq: 0 | 1 | | {{#ifeq: 0 | X | | }} }} | }}{{#if: | {{#ifeq: {{{5}}} | 1 | | {{#ifeq: {{{5}}} | X | | }} }} | }}{{#if: | {{#ifeq: {{{6}}} | 1 | | {{#ifeq: {{{6}}} | X | | }} }} | }}{{#if: | {{#ifeq: {{{7}}} | 1 | | {{#ifeq: {{{7}}} | X | | }} }} | }}{{#if: | {{#ifeq: {{{8}}} | 1 | | {{#ifeq: {{{8}}} | X | | }} }} | }}{{#if: | {{#ifeq: {{{9}}} | 1 | | {{#ifeq: {{{9}}} | X | | }} }} | }}{{#if: | {{#ifeq: {{{10}}} | 1 | | {{#ifeq: {{{10}}} | X | | }} }} | }}{{#if: 1 | {{#ifeq: 1 | 0 | | {{#ifeq: 1 | X | | }} }} | }}{{#if: 0 | {{#ifeq: 0 | 0 | | {{#ifeq: 0 | X | | }} }} | }}{{#if: 0 | {{#ifeq: 0 | 0 | | {{#ifeq: 0 | X | | }} }} | }}{{#if: 0 | {{#ifeq: 0 | 0 | | {{#ifeq: 0 | X | | }} }} | }}{{#if: | {{#ifeq: {{{5}}} | 0 | | {{#ifeq: {{{5}}} | X | | }} }} | }}{{#if: | {{#ifeq: {{{6}}} | 0 | | {{#ifeq: {{{6}}} | X | | }} }} | }}{{#if: | {{#ifeq: {{{7}}} | 0 | | {{#ifeq: {{{7}}} | X | | }} }} | }}{{#if: | {{#ifeq: {{{8}}} | 0 | | {{#ifeq: {{{8}}} | X | | }} }} | }}{{#if: | {{#ifeq: {{{9}}} | 0 | | {{#ifeq: {{{9}}} | X | | }} }} | }}{{#if: | {{#ifeq: {{{10}}} | 0 | | {{#ifeq: {{{10}}} | X | | }} }} | }}{{#if: 1 | | }}{{#if: 0 | | }}{{#if: 0 | | }}{{#if: 0 | | }}{{#if: | | }}{{#if: | | }}{{#if: | | }}{{#if: | | }}{{#if: | | }}{{#if: | | }}

	≥V1.0.X
	1	2	3	4	5	6	7	8	9	0

• Optionally, connect to the serial terminal to see the board's boot messages (via eCAM-EXT-Debug board on the red extension connector). If your Operating system does not install the drivers for a virtual comport, a USB-UART driver installation guide can be found here
• Use your Serial Terminal Program of your choice with the following settings:

Baudrate: 115200
FlowControl: NONE
Parity: None
Stop Bits: 1
Data: 8Bit

Starting up

• Connect to the Board with your serial terminal.
• Remove the cover from the lens.
• Connect 12V DC to the power connector on the back panel.
• Connect a monitor or TV via chinch cable on the back panel.
• If you like, connect Ethernet on the back panel.
• After power up a live video stream should be seen on the TV.

Web demo application

• Type ifconfig into the serial terminal to get the IP adress of the Argos®^2D D100.

eCM-BF561>ifconfig
Nof interfaces: 1

Int 0:
  MAC address- - - - - - - - - - : AC:DE:48:01:02:03
  DHCP enabled - - - - - - - - - : no
  IP address - - - - - - - - - - : 192.168.0.10
  Subnet mask  - - - - - - - - - : 255.255.255.0
  Gateway  - - - - - - - - - - - : 0.0.0.0

• If you want to change the IP address, type

ifconfig -ip xxx.xxx.xxx.xxx

• To enable DHCP type

ifconfig -dhcp yes

• For further information see

Command Reference

• Enter the IP address of the Argos®^2D D100 into your browser's address line.